αρχική
επικοινωνία
sitemap
NEWSLETTER

LOGIN
E-Mail: Συνθηματικό:
ΚΑΛΑΘΙ ΑΓΟΡΩΝ

Το καλάθι σας είναι άδειο

Ελληνικά
 
English
 
 

ΓΡΗΓΟΡΗ ΑΝΑΖΗΤΗΣΗ

 
 
Είστε εδώ: ΚΑΤΑΛΟΓΟΣ » ΤHΛΕΚΑΤΕΥΘΥΝΟΜΕΝΑ » ΑΥΤΟΚΙΝΗΤΑ » ΕΤΟΙΜΑ ΠΛΗΡΗ ΣΕΤ-ΗΛΕΚΤΡΟΚΙΝΗΤΑ » DF MODELS 3402, 1/6-HotRace XXL complete with 2 Lipo

135-3402 DF MODELS 3402, 1/6-HotRace XXL complete with 2 Lipo

 
 
 
Επιλέξτε για μεγέθυνση
DF MODELS  3402, 1/6-HotRace XXL complete with 2 Lipo
Κωδικός:
135-3402

Τίτλος:
DF MODELS 3402, 1/6-HotRace XXL complete with 2 Lipo

Κατασκευαστής:
DF MODELS

Η τιμή περιλαμβάνει ΦΠΑ
€ 906,31
Προηγούμενο Προϊόν   Επόμενο Προϊόν
 
 
 

ΠΕΡΙΓΡΑΦΗ:

DF MODELS  3402, 1/6-HotRace XXL Truggy, πλήρες σετ, μεγάλες επιδόσεις, 70χλ/ω, full extra, και τηλεκατεύθυνση 2.4G, με LCD display, computerised. Διατίθεται μέσα σε μεταλλικό μπαούλο για την μεταφορά, 
 είναι τεράστιο ! .... είναι σε κλίμακα 1/6 !! 

 

ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ:

   είναι τεράστιο ! γιατί είναι 1/6 !!

The model is an all-wheel drive RC car chassis with a pre-installed brushless electric motor and a 2.4 GHz receiver station, a programmed, electronic speed controller, steering servo with metal transmission and two 2S LiPo rechargeable batteries. 
The ready-printed and ready-cut-out body make for a spectacular look, right out of the box. 

This model is intended both for operation on indoor tracks as well as operation outdoors. 
The double-deck chassis made of anodised aluminium is light and torsion-resistant. Plastic covers screwed onto the chassis provide the built-in components protection against splashed water and pebbles thrown up. 
The two 2S LiPo rechargeable batteries enable symmetrical weight distribution by the longitudinal axis and ensure immense power output. A low-maintenance brushless motor provides satisfaction with higher power, greater torque and a higher efficiency factor than conventional brushed motors. A heat sink with a fan attached ensures heat dissipation even under the most severe conditions. 
The unit is powered by the motor pinion on the centre differential. From there one drive shaft each made of metal meshes in the encapsulated differentials of the front and rear axles, thus bringing about four-wheel drive. The differentials in the front and rear axles provide for speed compensation between the wheel on the inside and the wheel on the outside of curves and has metal gears. 

The model is entyrely ball-bearing-mounted. A programmable electronic speed controller KL-80 with a fan attached is geared in optimum fashion to the brushless motor and provides satisfaction through excellent starting behaviour, acceleration and excellent synchronisation. 
The high-performance RS 90 MGBB steering servo with metal gearbox has high controlling torque amounting to 9,0 kgcm (88,3 Ncm) and high control speed with maximum stability. A servo saver also provides protection for the servo against sharp impacts against the wheels. 
Anti-roll bars on front and rear axle each connect the bottom suspension arms of one axle in such a way, that the respective other wheel is deflected along with a deflected wheel. The roll behaviour in curves of the vehicle is thus curbed and driveability improved. 

In this 2.4 GHz remote control set with two proportional channels and one adjustable switch channel, you own a radio remote control system that is ideally suited primarily for model cars and model ships. Its proportional control channels allow 2 control functions to be remotely controlled independently of one another. 
Each time the unit is switched on, the link between the transmitter and the receiver is made automatically by AFHDS (Automatic Frequency Hopping Digital System). 

Dimensions and weight: 

- Overall length 688 mm 
- Wheelbase 480 mm 
- Width front/rear 430 mm 
- Height 232 mm 
- Ground clearance 70 mm 
- Weight with/without rechargeable LiPo drive batteries 4670 g / 4040 g 

Vehicle will be delivered in a safe transport case! 

 

Engine: 
- brushless electric motor, pre-installed 
- Operating voltage 2 x 7,4 V 
- KV (revolutions/V) 1500 
- No-load current 2.0 A 
- Length 74 mm 
- Diameter 36 mm 
- Weight 360,6 g 
- Length of the motor shaft 90 mm 
- Shaft diameter Ø 5 mm 

Power transmission: 
- All-wheel drive, 3 differentials 
- All driving axles ball-bearing-mounted 

Chassis frame: 
Front-wheel suspension Double-wishbone suspension, tensioning screw in the upper wishbone rear-wheel suspension: Double-wishbone suspension Tensioning screw 
in the upper wishbone Track rods: Tensioning screw in the right and left track rod parts 

Chassis: 
Twin-deck chassis made of anodised aluminium extremely light, strong and torsion-resistant 
Upper deck made of anodized Aluminium Shock absorber bridges made of fibre-reinforced plastic Raised plastic shells on the sides 

Suspension: 
Flat coil springs with aluminium oil-pressure shock absorbers 
Spring preload adjustable by means of threaded rings, Variable articulation points. 

Tires: 
- Front/rear: High-grip multi-spike tyres with filler strips 
- Ø 150 mm, width 70 mm 

Speed controller 
- Controller KL-80 
-Continuous current 80 A 
- Peak current 380 A 
- Resistance 0.0006 ohm 
- Dimensions (without fan) (LxWxH) 58 x 46.5 x 35 mm 
- Weight 105 g (without cables) 

Transmitter 
- # of channels 3 
- Frequency 2.4 GHz 
- 2,4 GHz system AFHDS 
- HF range 2,40 to 2,48356 GHz 
- Band width 500 Hz 
- Modulation GFSK 
- Digital signal (1024 steps) 
- Application car, boat 
- PC link (DSC port) 3.5mm jack plug 
- Built-in charging socket 
- Operating voltage 12 volt (8 x AA cell) 
-Weight 395 grams 
- Dimensions 154 x 127 x 270 mm 

Reciever 
- # of channels 3 
- Frequency 2.4 GHz 
- Application car, boat 
- Modulation GFSK 
- Resolution 1024 steps 
- Operating voltage 4.5-6 volt DC 
- Weight 5 grams 
- Dimensions (l x w x h) 37.6 x 22.3 x 13 mm 
- Antenna wire length 170 mm 

Servo: 
- Servo RS 90 MGBB 
- Features Metal gears, two ball bearings 
- Operating voltage 6 V 
- Actuating speed (sec/60°) 0.16 s 
- Actuating torque 9.0 kg/cm (88.3 Ncm) 
- Weight 56 g 
- Dimensions (LxWxH) 41.3 x 20.3 x 38.7 mm 

Scope of supply 
- A 4WD electric RC Truck with: 
- Twin-deck chassis made of anodised aluminium 
- 4 rims with multi-spike wheels 
- 4 infinitely variable aluminium oil-pressure shock absorbers. 
- Truck body, cut-out and printed 
- 2.4 GHz receiver, pre-installed and pre-adjusted 
- Brushless electric motor with heat sink and fan, pre-installed 
- Programmable, KL-80 electronic speed controller with fan, pre-installed 
- RS 90 MGBB steering servo, pre-installed 
- 2.4 GHz 3-channel remote-control transmitter 
- Communication plug 
- USB cable for connecting the transmitter to the PC, for controlling simulation programs 
- Operating Instructions for the model, the remote control unit and the speed controller


BRUSHLESS  SUPER POWER  
 
 

ΠΕΡΙΣΣΟΤΕΡΕΣ ΦΩΤΟΓΡΑΦΙΕΣ:

DF MODELS  3402, 1/6-HotRace XXL complete with 2 Lipo
Επιλέξτε για μεγέθυνση
DF MODELS  3402, 1/6-HotRace XXL complete with 2 Lipo
Επιλέξτε για μεγέθυνση
DF MODELS  3402, 1/6-HotRace XXL complete with 2 Lipo
Επιλέξτε για μεγέθυνση
DF MODELS  3402, 1/6-HotRace XXL complete with 2 Lipo
Επιλέξτε για μεγέθυνση
DF MODELS  3402, 1/6-HotRace XXL complete with 2 Lipo
Επιλέξτε για μεγέθυνση
 

ΠΑΡΟΜΟΙΑ ΠΡΟΙΟΝΤΑ:
 135-3402DF MODELS 3402, 1/6-HotRace XXL complete with 2 Lipo 
 
ΒΑΣΙΚΕΣ ΚΑΤΗΓΟΡΙΕΣ:
ΥΠΟΚΑΤΗΓΟΡΙΕΣ:
KΛIMAKA:
ΚΑΤΑΣΚΕΥΑΣΤΗΣ:
 
ΕΙΔΙΚΕΣ ΚΑΤΗΓΟΡΙΕΣ:
ΚΩΔΙΚΟΣ ΚΑΤΑΣΚΕΥΑΣΤΗΣ::
ΛΕΞΗ-ΚΛΕΙΔΙ::
 
 
Στις τιμές περιλαμβάνεται Φ.Π.Α.
 
Copyright © 2016 Designed & Developed by ICOP